How to Clean a Gun
Cleaning guns is an essential activity for any gun owner. A weapon that not appropriately cleaned will become inaccurate and may even cause a malfunction. Here is a proven method of cleaning a gun.
When cleaning your weapon, remove all magazines from your gun and make sure it discharge. Check the room to make sure it is empty. At the same time, check if the parts are damaged.
After the inspection, start removing your weapon on site. Most firearms are relatively easy to remove, but you should consult your owner's manual to determine the correct procedure. If you cannot find your user guide, you may be able to find replacements by searching the web. At the end of your wiping, you usually have access to the barrel and all of the pistol's bolts.
The first thing to clean is the barrel. Check the barrel to make sure there are no obstacles. Then take a cleaning stick and place a cleaning plaster at the end. If possible, be sure to pull the cleaning plaster toward the mouth and not far from the mouth. After a few scans, it is time to apply drilling solvent to the cylinder. The best way to do this is to use a brush on the end of your cleaning stick soaked in water. Alternatively, you can dip a cleaning plaster in a solvent and let it run. After the solution has coated the cylinder, allow it to sit in the bottle for at least ten minutes before cleaning it further. It gives the drilling solvent the ability to absorb and loosen the residue.
In the meantime, it's a good idea to move on to the other parts of the weapon. You can start by cleaning the frame of your gun. It can be achieved by spraying gun oil on a cleaning plaster and rubbing the frame. You need to make sure that you are caught in the cracks of your weapon, although there is no need to go deep into the action. To get into the cracks, you can squeeze your cleaning plaster with a brush. The most important parts of the cleaned are the parts that move during shooting, e.g., B. the rails of a semi-automatic pistol.
After cleaning the frame, you will also need to clean all of the screw assemblies. Most guns allow you to disassemble the screw assembly, which is a good idea for cleaning. Be sure to clean the area around the striker and the ejector. If the residue sticks too much, use a brass brush dipped in solvent to loosen the dirt. Finish cleaning with a cleaning spray sprayed with gun oil.
After sitting in the barrel for more than 10 minutes, it's time to finish cleaning. Run a brass brush at the end of your cleaning stick to remove and loosen the residue in the barrel. If you have done this three or four times, pass a chemical cleaning compound several times through the barrel. Once the patch is clean, you know you did. If your barrel is particularly dirty, you may need to apply more solvent with a hole and repeat the above procedure.
Once everything clean, apply a light coat of oil to the moving parts and reassemble your weapon. Make sure it works properly. Before storing your gun, wipe it off with a silicone cloth to protect it from rust and wipe off excess oil. Read more
When cleaning your weapon, remove all magazines from your gun and make sure it discharge. Check the room to make sure it is empty. At the same time, check if the parts are damaged.
After the inspection, start removing your weapon on site. Most firearms are relatively easy to remove, but you should consult your owner's manual to determine the correct procedure. If you cannot find your user guide, you may be able to find replacements by searching the web. At the end of your wiping, you usually have access to the barrel and all of the pistol's bolts.
The first thing to clean is the barrel. Check the barrel to make sure there are no obstacles. Then take a cleaning stick and place a cleaning plaster at the end. If possible, be sure to pull the cleaning plaster toward the mouth and not far from the mouth. After a few scans, it is time to apply drilling solvent to the cylinder. The best way to do this is to use a brush on the end of your cleaning stick soaked in water. Alternatively, you can dip a cleaning plaster in a solvent and let it run. After the solution has coated the cylinder, allow it to sit in the bottle for at least ten minutes before cleaning it further. It gives the drilling solvent the ability to absorb and loosen the residue.
In the meantime, it's a good idea to move on to the other parts of the weapon. You can start by cleaning the frame of your gun. It can be achieved by spraying gun oil on a cleaning plaster and rubbing the frame. You need to make sure that you are caught in the cracks of your weapon, although there is no need to go deep into the action. To get into the cracks, you can squeeze your cleaning plaster with a brush. The most important parts of the cleaned are the parts that move during shooting, e.g., B. the rails of a semi-automatic pistol.
After cleaning the frame, you will also need to clean all of the screw assemblies. Most guns allow you to disassemble the screw assembly, which is a good idea for cleaning. Be sure to clean the area around the striker and the ejector. If the residue sticks too much, use a brass brush dipped in solvent to loosen the dirt. Finish cleaning with a cleaning spray sprayed with gun oil.
After sitting in the barrel for more than 10 minutes, it's time to finish cleaning. Run a brass brush at the end of your cleaning stick to remove and loosen the residue in the barrel. If you have done this three or four times, pass a chemical cleaning compound several times through the barrel. Once the patch is clean, you know you did. If your barrel is particularly dirty, you may need to apply more solvent with a hole and repeat the above procedure.
Once everything clean, apply a light coat of oil to the moving parts and reassemble your weapon. Make sure it works properly. Before storing your gun, wipe it off with a silicone cloth to protect it from rust and wipe off excess oil. Read more
Comments
Post a Comment